Samsung Galaxy S22 Battery Replacement (2024)

• Heat an iOpener and apply it to the bottom edge of the back cover for two minutes.

• A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the phone—the display and internal battery are susceptible to heat damage.

• While you wait for the adhesive to soften, note the following:

• There's adhesive securing the back cover around the perimeter of the frame.

• The adhesive is strongest in the bottom right and top left corners.

• Apply a suction handle to the back cover, as close to the bottom edge as possible.

• Pull up on the suction handle with strong, steady force to create a gap between the cover and the frame.

• If you have trouble creating a gap, apply more heat to further soften the adhesive. Follow the iOpener instructions to avoid overheating.

• Insert an opening pick into the gap.

• Slide the pick back and forth along the bottom edge to slice through the adhesive.

• Leave the pick inserted in the bottom left corner to prevent the adhesive from resealing.

• Apply a heated iOpener to the left edge of the back cover for two minutes.

• Insert a second opening pick at the bottom left corner.

• Slide the pick to the bottom of the camera bezel to slice the left adhesive.

• Only insert the pick up to 5mm, as you may damage the antenna flex cable or the power button cable.

• Leave the pick in to prevent the adhesive from resealing.

• Heat an iOpener and apply it to the right edge of the back cover for two minutes.

• Insert a third opening pick at the bottom right corner.

• If the adhesive has resealed, insert the pick closer to the bottom edge.

• Slide the pick to the top right corner to slice the adhesive.

• Leave the pick in the top right corner to prevent the adhesive from resealing.

• Heat an iOpener and apply it to the top edge of the back cover for two minutes.

• Insert an opening pick in the gap at the top right edge.

• Slide the pick across the top edge and around the top left corner to slice the remaining adhesive.

• Only insert the pick up to 4mm, as you may damage the rear cameras or flash.

Buy

• Grab and remove the back cover.

• If your cover is still sticking to the frame, slide an opening pick around the perimeter until the cover completely separates.

• During reassembly:

• This is a good point to power on your phone and test all functions before sealing it up. Be sure to power your phone back down completely before you continue working.

• Remove any adhesive chunks with a pair of tweezers or your fingers. Apply heat if you're having trouble separating the adhesive.

• To apply new adhesive, follow this guide.

• Use the pointed end of a spudger to pry and disconnect the wireless charging coil from the motherboard.

• To re-attach press connectors, carefully align and press down on one side until it clicks into place, then repeat on the other side. Don't press down on the middle. If the connector is misaligned, the pins can bend and cause permanent damage.

• If you're using the Samsung Self Repair Kit, take a moment to identify your screws and label them accordingly:

• Label the bag with the most screws and the colored bag #3428.

• If you're replacing the screen and battery, label the clear bag with two screws #3229.

• Use your Phillips screwdriver to remove the six 3.5mm-long screws securing the wireless charging coil.

• If you're reassembling with the Samsung Self-Repair kit, be sure to replace the screws with the new ones labeled #3428.

• Use your Phillips screwdriver to remove the seven 3.5mm screws securing the loudspeaker.

• If you're reassembling with the Samsung Self-Repair kit, be sure to replace the screws with the new ones labeled #3428.

• Insert the pointed end of your spudger between the upper left corner of the loudspeaker and the frame.

• Pry up to unclip the loudspeaker from the frame.

• During reassembly, press around the perimeter of the loudspeaker to engage the clips.

• Grab and remove the wireless charging coil and loudspeaker from the frame.

• Do not separate the charging coil from the loudspeaker.

• Use the pointed end of your spudger to pry up and disconnect the battery press connector.

  See Also

  How To Change Batteries On Samsung Smart TV Remote For Optimal Performance

• Use the pointed end of your spudger to pry up and disconnect both interconnect cables from the motherboard.

• Use the pointed end of your spudger to pry up and disconnect both interconnect cables from the charging board.

• Grab and remove the two interconnect cables from the frame.

• During reassembly, orient the cables so the "main" ends are toward the top of the phone and the "sub" ends are toward the bottom.

• Use the pointed end of your spudger to pry up and disconnect the power and volume button press connector.

• Use the pointed end of your spudger to pry up and disconnect the left 5G mmWave antenna press connector.

• During reassembly, make sure this cable and the power and volume button cable are under the battery cable.

• Use your Phillips screwdriver to remove the two 3.5 mm‑long screws securing the left 5G mmWave antenna.

Buy

• Insert the pointed end of your spudger between the lower screw mount of the antenna bracket and the frame.

• Pry up on the bracket until you can grab it with blunt nose tweezers or your fingers.

• Remove the left 5G mmWave antenna.

• Use the pointed end of your spudger to pry up and disconnect the screen press connector from the motherboard.

• Use the pointed end of your spudger to pry up and disconnect the screen press connector from the bottom left corner of the phone.

• Remove the screen cable.

• Strong adhesive secures the battery to the frame.

• Use a pipette or syringe to apply a few drops of highly-concentrated isopropyl alcohol (greater than 90%) between the right edge of the battery and frame.

• Elevate the right edge of the phone for one minute to allow the isopropyl alcohol to flow under the battery and soften the adhesive.

• Take care not to puncture the battery—it can leak dangerous chemicals and/or catch fire.

• Apply a suction cup to the battery, as close to the center of the right edge as possible.

• Insert the tip of an opening pick between the right edge of the battery and frame.

• Push the opening pick down and rotate it so the long end is between the battery and frame.

• Take care not to crease or bend the battery—it can leak dangerous chemicals and/or catch fire.

• Pull up on the suction cup with strong, steady force while prying the battery up with the opening pick.

• Maintain constant pressure on the pick and suction cup until the battery separates from the frame.

• Be patient and allow time for the adhesive to separate. If the battery doesn't budge, apply a few more drops of isopropyl alcohol and try again.

• Remove the battery.

• Follow this guide to install your new battery.